No.0 Machinery Get a quote +86 135 8587 6500
Home/Products/Plastic Sheet Bending Machines/No.0 PP Sheet Bending Machine
PLASTIC SHEET BENDING

No.0 PP Sheet Bending Machine

LH-1500(ZH-B) – LH-3000(ZH-B)Four folds, one seam, no air leak.
No.0 PP Sheet Bending Machine LH-1500(ZH-B) – LH-3000(ZH-B) — pp air ducts
up to 25 mm(0.98 in)Sheet thickness
1500–3000 mm(4.9 ft–9.8 ft)Bending length
60°–180°, adjustableBending angle
50 mm(2.0 in)Minimum flange

A square PP duct needs four welded seams. This machine folds all four edges from one sheet and leaves a single longitudinal seam — the duct no longer leaks air, the tank no longer leaks water.

What it solves

01
Four seams per duct

Every seam is a leak path and an hour of welding.

Welding eats labour

Weld, grind, leak-test: the sequence multiplies the cost of a simple duct.

Thin PP whitens

PP corners stress-whiten and crack after a few flex cycles.

Core value

02
01

Four folds, one seam.

02

Corners that do not whiten.

03

Ducts from 300 mm side upwards.

How it works

03
  1. 01
    Buffered bending

    The stroke is damped, so stress at the corner stays low and the material does not whiten.

  2. 02
    Line heating

    Only the fold line softens; surface finish and flatness are untouched.

  3. 03
    Four edges in sequence

    Ducts and tanks are folded edge by edge with one clamping, leaving one seam.

  4. 04
    Duct capability

    PP air ducts with a minimum side of 300 mm can be formed directly.

Specifications

04
Sheet thicknessup to 25 mm (0.98 in)
Bending length1500–3000 mm (4.9 ft–9.8 ft)
Bending angle60°–180°, adjustable
Minimum flange50 mm (2.0 in)
Power6–10 kW
Voltage / air380 V / 0.5 MPa

Advantages

05

Forming

  • Four edges folded from one sheet, one longitudinal seam.
  • Corners stay white-free and survive repeated flexing.
  • Tanks can be water-tested straight off the machine.

Operation

  • Temperature and dwell set by sheet thickness; changing material is a parameter change.
  • Automatic and manual modes, foot pedal supported.
  • Front and rear stops for repeatable bend lines.

Structure

  • Aluminium table and one-piece frame keep long panels straight.

What it bends

06
PP air ductsPP water tanksPackaging boxesPlating barrelsChemical tanks

Machine detail

No.0 PP Sheet Bending Machine — detail 1 (LH-1500(ZH-B) – LH-3000(ZH-B))No.0 PP Sheet Bending Machine — detail 2 (LH-1500(ZH-B) – LH-3000(ZH-B))

Video

Send a sample sheet

Post a 200 × 200 mm offcut with material and thickness noted; we bend it to your angle and send photos plus video within 48 hours.

Request a trial bend

Also known as

07
PP Bending MachinePP Sheet BenderPP Duct Bending MachinePP Tank Bending MachinePolypropylene Bending MachinePlastic Duct Bender

All names above refer to this machine — see the full alias index.

FAQ

08
Can PP ducting be formed directly?

Yes. Four edges are folded from one sheet, leaving one longitudinal seam; ducts from 300 mm side upwards.

Will the corners whiten?

No. The bending stroke is buffered, keeping stress at the corner low.